Sunday, August 23, 2009

Fabulous, D.I.Y. Cupcake Stands!


Good riddance to a traditional cake - let them eat cupcakes! That's right, our guests will be able to choose from three delicious cupcake flavors: chocolate raspberry, chocolate abuelita (like a cinnamon chocolate), and lemon raspberry.

We are expecting approximately 160 guests. Well, if you have researched cupcake stands, then you know most stands don't hold that many. The reception venue usually puts some of the cupcakes out at the beginning of the reception and continues to fill the stand as guests help themselves. Furthermore, to rent a stand can be expensive ($80-$150 per stand). So, we asked ourselves, why not make cupcake stands able to hold ALL of the cupcakes and then sell them after the wedding?

Future Hubby has a friend who owns his own woodworking studio, and the two of them cut long planks of paint-grade plywood (purchased from Lowe's) into smaller squares. They then used a special woodworking tool (that's the technical term - ha ha ha!) to add a decorative edge that resembles crown moulding. After getting the measurements of one cupcake from our cupcake vendor (Betty's Sweet Dreams), we determined how many cupcakes would be able to fit on each layer. Here is the schematic we designed:

Each stand can hold seventy-six cupcakes, times two stands, that's 152 cupcakes. That leaves eight cupcakes leftover, plus the six-inch cake we ordered to have something to cut during the reception. Solution: a two-tiered stand for the cake and remaining cupcakes!



A trip to Home Depot resulted in three lengths of wood dowel used to hang clothing in a closet. These poles would serve as the center posts in the middle of each stand. But how to attach each layer of the stand to the pole? Just use the brass caps that normally attach to the closet wall and hold the pole in place! After many frustrating attempts to keep each layer level (seriously, this was not as easy as you might think!), Future Hubby was able to attach a brass cap under each layer and screw them into the center pole for support. (He discovered that assembling them upside down was easier.)


And here are all three stands ready to paint!



But wait! What are those cute little feet holding the stands off the floor? Michael's has an entire row of unfinished wood products, including little hexagonal boxes. After digging through all miniature boxes (the Michael's staff must think I'm a pain in the butt!), I purchased twelve boxes, ditched their lids, and Future Hubby attached them to the bottom of the stands using short screws.
We used semi-gloss white paint (there is a new line that is a combination of primer and paint) purchased from the Home Depot to paint the stands. Since these would sit on a table at the reception, we also painted the undersides for when short people (like me!) came forward for a cupcake.


If you are interested in purchasing these after mid-October (and live in the Los Angeles area), leave a comment on this posting and let me know!

TOTAL COST FOR ALL THREE STANDS:
Paint-grade plywood (2 pieces of 16"x72"x21/32"): $28.48
Paint-grade plywood (1 piece of 16"x36"x21/32"): $7.23
8' of closet dowel/pole: $10.80
14 brass closet pole holders: $23.66
12 mini boxes made into feet: $12.00
1 quart of white paint: $14.98
TOTAL COST: $96.15

8 comments:

Jacquie said...

have you sold these yet? They are fabulous! If you haven't sold them I'd love to inquire about purchasing them. thistaurusisatiger22@gmail.com my blog address is batterorworse.blogspot.com thanks!

S said...

I can't wait to start this diy project! thanks :)

Creations By Cindy said...

Love this idea!

Anonymous said...

what is the height between each shelve

SritaB! said...

Donyou drill a hole in the center of each layer?

Unknown said...

Courage is what it takes to stand up and speak; courage is also what it takes to sit down and listen. See the link below for more info.


#stand
www.ufgop.org


moshrabbi121 said...

This is the precise weblog for anyone who wants to search out out about this topic. You notice a lot its virtually exhausting to argue with you (not that I really would need…HaHa). You undoubtedly put a brand new spin on a subject thats been written about for years. Nice stuff, simply great! casino bonus

Anonymous said...

How long are the poles in between each layer?